Ponding water that never drains
We add tapered insulation or new drains to create positive slope. We check the deck for sagging and reinforce it if needed. Water flows off the roof within 48 hours of a storm.
Flat Roofing in New York demands a contractor who understands lake-effect snow, coastal wind, and everything between. Roofnexa NY installs and repairs flat roof systems for commercial buildings, multi-family properties, and homes statewide. Since 2014 we have handled membrane, modified bitumen, and coating work from Buffalo to Long Island. If your roof ponds, leaks, or has reached the end of its service life, we assess it, price it, and fix it.
Tell us what is happening. Our local team will confirm your visit shortly.
Call Now (315) 503-7248 → No spam. No obligation. Just practical help.
Flat Roofing in New York is the design, installation, and repair of low-slope roof systems that shed water through drainage rather than pitch. Most flat roofs here use single-ply membrane, modified bitumen, or built-up systems. We install Firestone and Carlisle SynTec membranes, torch-down modified bitumen, and fluid-applied coatings. Every job starts with a deck inspection, moisture scan, and drainage calculation so the system matches your building, not a catalog.
New York flat roofing gets tested hard. Buffalo and Rochester see lake-effect snow loads that stress seams. Long Island and Westchester deal with nor'easters and summer UV that cook membrane. Older buildings in Kingston and Beacon often have failing flashing and ponding water that never drains. If you need flat roof repair in New York for leaks, we trace the source with infrared and moisture meters before we quote a fix.
Every flat roofing project we do includes a full assessment, written estimate, tear-off, deck inspection, and new membrane installation. Here is what you get when you hire us.
We walk the roof, scan for moisture, check drainage, and photograph every problem area. You get a written report with findings and photos within 24 hours.
We remove the old membrane, insulation, and flashing. We inspect the deck and replace any rotten sheathing. All debris goes into dumpsters we bring and haul away.
We install underlayment, insulation, and your chosen membrane system. We use Firestone, Carlisle SynTec, or GAF materials. Every seam is heat-welded or adhered per manufacturer spec.
We replace all flashing, install new drains if needed, and make sure water flows off the roof. Ponding water is the number one cause of flat roof failure. We fix it.
We test drainage, check every seam, and clean the site. You get a walkthrough, manufacturer warranty paperwork, and our 5-year workmanship warranty.
We walk the roof, check drainage, scan for moisture, and photograph every problem area. You get a written report with findings and photos within 24 hours. Most assessments take 45 to 90 minutes depending on roof size and access.
We price the job by scope, not by guess. Your estimate lists membrane type, insulation thickness, flashing details, and labor. We explain what drives the cost and what you can defer. No pressure, no same-day discount games.
Once you approve, we schedule the crew and order materials. We protect landscaping, mask windows, and set up dumpsters. For commercial buildings, we coordinate around your business hours so you stay open. Most jobs start within 7 to 14 days of approval.
We remove the old roof, inspect the deck, and replace any rotten sheathing. Then we install underlayment, insulation, and the membrane system. A 2,000-square-foot roof takes two to four days. We run magnetic sweeps at the end of each day to catch roofing nails.
We test drainage, check every seam and flashing, and clean the site. You get a walkthrough, warranty paperwork, and maintenance instructions. We do not leave until you have seen the finished work and signed off.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Fastens base sheets and insulation to the deck. We use pneumatic guns for consistent depth and speed on large commercial roofs.
Strips old membrane and underlayment during tear-off. Keeps the deck intact so we can inspect for rot.
Hand-nails flashing and edge metal where a nail gun would overdrive. Used for detail work around drains and penetrations.
Cuts membrane, insulation, and flashing to size. We go through dozens of blades on a typical flat roof job.
Marks straight lines for membrane layout and flashing alignment. Critical for a clean, professional-looking install.
Applies sealant around flashing, drains, and penetrations. We use compatible sealants that match the membrane system.
Drives fasteners for edge metal, termination bars, and equipment pads. We use cordless drills for speed and mobility.
A 15,000-square-foot warehouse roof in Buffalo had three layers of old membrane, ponding water, and active leaks over the loading dock. The owner was tarping every storm.
We tore off all three layers, replaced 12 sheets of rotten decking, installed tapered insulation, and put down 60-mil TPO. The roof now drains within 24 hours and has not leaked in two winters.
A homeowner in West Islip had a flat roof over a family room addition. Water ponded after every rain and leaked into the ceiling. Two contractors patched it without fixing the drainage.
We added tapered insulation to create slope, installed a new drain, and replaced the membrane. The leak stopped immediately. The ceiling was repaired and repainted.
A property manager in Scarsdale had a 30-year-old flat roof on a six-unit building. The roof was not leaking yet but was past its service life and had failing flashing.
We applied a silicone restoration coating over the existing membrane after repairs. The coating added 10 years of life at 40 percent of replacement cost. The flashing was replaced and the roof is now under warranty.
Flat roofs fail in predictable ways. Here are the problems we see most often and how we fix them before they cost you thousands in interior damage.
Ask a pro →We add tapered insulation or new drains to create positive slope. We check the deck for sagging and reinforce it if needed. Water flows off the roof within 48 hours of a storm.
We clean the seam, apply primer, and heat-weld or adhere a new membrane strip. For flashing, we replace the metal and reseal it with compatible sealant. We test with water before we leave.
We tarp the roof the same day you call. Then we replace the damaged section, re-secure the membrane, and check the rest of the roof for lifted edges.
We assess whether a coating will buy you five more years or if replacement is the better investment. We give you both prices and let you decide.
“Our warehouse roof in Buffalo was leaking for two years. Three other contractors just patched it. Roofnexa found the real problem, replaced the flashing, and installed new TPO membrane. That was last winter and we have not had a drop since. They tarped the roof the same day I called.”
Dave R.Commercial Property Owner, Buffalo
✓ Verified“We have a flat roof over our addition in West Islip. It started ponding after every storm. Roofnexa added a drain and recoated the whole thing. They were in and out in two days. The price was exactly what they quoted. No surprises.”
Maria S.Homeowner, West Islip
✓ Verified“I manage six buildings in Scarsdale and Roofnexa handles all our flat roof maintenance. They come twice a year, clean the drains, and check the seams. We have not had an emergency leak in three years. That is worth every penny.”
James L.Property Manager, Scarsdale
✓ VerifiedMost flat roof replacements in New York run $8 to $16 per square foot installed, or $16,000 to $32,000 for a 2,000-square-foot roof. Repairs typically cost $600 to $3,500 depending on the damage. Membrane type, insulation thickness, deck condition, and access all affect the price. We give you a written estimate after we inspect the roof.
For most New York buildings, 60-mil TPO or EPDM membrane is the best balance of cost and performance. TPO handles UV and ponding water well. EPDM lasts longer in cold climates. Modified bitumen is a good choice for high-traffic roofs. Firestone and Carlisle SynTec make the systems we install most. We recommend based on your building, not a sales quota.
A properly installed flat roof lasts 20 to 30 years in New York with annual maintenance. Without maintenance, expect 12 to 18 years. Snow load, freeze-thaw cycles, and UV exposure all shorten the life. We inspect and clean drains twice a year to get you the full service life.
Roofnexa NY installs flat roofs across New York State. We are a licensed home improvement contractor with Firestone and Carlisle SynTec certifications. Our crews handle tear-off, deck repair, insulation, membrane, and flashing. We serve Buffalo, Saratoga Springs, West Babylon, New City, and every city in between. Call us for a free assessment.
Roofnexa NY delivers flat roofing in New York across the entire state. From Buffalo to Saratoga Springs, West Babylon to New City, we handle commercial and residential flat roof projects with the same crew and the same standards. Here are some of the cities we serve.
Call Roofnexa NY at (315) 503-7248 for a free flat roof assessment. We serve Buffalo, Saratoga Springs, West Babylon, New City, and all of New York State. Licensed, insured, and ready to work.
Get Free Estimate (315) 503-7248 →Call (315) 503-7248 or email info@roofnexany.com and we will schedule a free inspection at your property. We answer the phone 24/7 for emergencies, and standard estimates are booked within two business days. Tell us your address and what you are seeing, and we will tell you what it takes to fix it.