Standing seam panels installed by a licensed New York contractor, start to finish.

Metal Roofing in New York Built for Snow, Ice, and Salt Air

Metal Roofing in New York is a long-life roof system of interlocking steel or aluminum panels that sheds snow, resists ice dams, and holds up to lake-effect winters and coastal salt air. We install and repair standing seam and exposed-fastener systems for homeowners, landlords, and commercial property owners statewide. If your asphalt shingles are curling, granule-bare, or patched after last winter, metal is the last roof you will likely need to buy.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

Call Now (315) 503-7248 → No spam. No obligation. Just practical help.
Metal Roofing you can count on
Careful work. Honest options.
About this service

Metal Roofing in New York: What It Is and Why It Works Here

Metal Roofing in New York is a panel-based roof system installed over a deck with ice and water shield, synthetic underlayment, and concealed clips or exposed fasteners, depending on the profile. Standing seam panels are roll-formed from 24- or 26-gauge steel with a Kynar 500 finish, then locked together with a mechanical seamer so there are no exposed screws on the field of the roof. Exposed-fastener panels use neoprene-washered roofing nails or screws and cost less per square, which makes them a common choice on barns, garages, and rental properties.

New York roofs take a beating that most of the country does not see. Lake-effect towns get 100-plus inches of snow in a season, the Hudson Valley and Finger Lakes swing from 95-degree July afternoons to minus-10 January nights, and Long Island's south shore sits in salt spray and hurricane-wind zones. Metal roof installation New York homeowners ask for is usually driven by one of three things: ice dams backing water under the shingles, storm damage insurance claims, or a roof that has already been patched twice. We size every panel, clip, and fastener for the wind and snow load your town actually requires.

  • ✓ Snow Slides Off
  • ✓ 50-Plus Year Service Life
  • ✓ Lower Cooling Load
  • ✓ Storm and Hail Resistant
What's included

What Our Metal Roofing Service Includes

Every metal roof we install comes with the full system: deck prep, underlayment, ice and water shield, panels, flashing, vents, and cleanup. We do not sell panels as a standalone product, because a metal roof is only as good as the layers under it.

✓

Full Tear-Off and Disposal

We strip the old shingles or metal panels, haul them away, and inspect the deck for rot. Soft sheathing gets replaced before any new material goes down. Dumpster and disposal fees are in the price.

✓

Ice and Water Shield

A self-adhering membrane goes at the eaves, valleys, and around every penetration. This is the layer that stops ice dams from backing water under the panels during a January thaw.

✓

Custom-Cut Metal Panels

Standing seam panels are roll-formed to your roof's exact dimensions, which means fewer seams, less waste, and a cleaner finished line. Exposed-fastener panels are cut and nested on site.

✓

New Flashing and Boots

Chimney flashing, step flashing, drip edge, pipe boots, and skylight surrounds are all replaced. Reusing old flashing is the number one cause of leaks on a new metal roof.

✓

Ridge Vents and Ventilation

We balance intake at the soffit with ridge vents at the peak so the attic breathes. Proper ventilation prevents attic condensation and keeps the underside of the panels from sweating in winter.

✓

Magnet Sweep and Final Walkthrough

We run a magnet over the lawn and driveway for stray roofing nails, hose-test every penetration, and walk the finished roof with you. Warranty paperwork is handed over before we leave.

How it works

How Our Metal Roof Installation Process Works

01

Free Inspection

We walk the roof, check the deck from the attic, and photograph every problem area: flashing failure, ice dam staining, soft spots, and attic condensation. You get a written scope the same day, plus a recommendation on whether metal makes sense or a repair will buy you time.

02

Panel Layout and Order

We measure every plane, valley, and penetration, then order panels cut to length from the manufacturer. Standing seam panels are roll-formed to your exact roof dimensions, which means fewer seams and less waste. Lead time on custom panels typically runs two to four weeks.

03

Tear-Off and Deck Prep

Crews strip the old shingles with a shingle remover and pry bar, then inspect the deck for rot and re-nail any soft sheathing. We install ice and water shield at the eaves and valleys, then synthetic underlayment across the field. Roofing felt is a backup layer, not a substitute.

04

Panel Install and Flashing

Panels go down over concealed clips or exposed fasteners, locked with a mechanical seamer on standing seam. Every chimney, skylight, and wall gets new roof flashing, and we caulk with a gun rated for the temperature swings your region sees. Ridge vents and drip edge go on last.

05

Final Walkthrough

We magnet-sweep the yard for roofing nails, test every penetration with a hose, and walk the roof with you to show the finished seams, flashings, and vents. You get the manufacturer warranty paperwork and our workmanship warranty in hand before we pull out of the driveway.

Tools & methods

Tools and Methods We Use on Metal Roofs

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Standing Seam Mechanical Seamer

Locks the vertical legs of adjacent panels together into a single watertight seam. We use a powered seamer on long runs and a hand seamer at the ends and around penetrations.

Roofing Nail Gun and Power Drill

Fastens clips, underlayment, and exposed-fastener panels. We set the depth so the neoprene washer seats without crushing, which is where most leaks start on metal roofs.

Shingle Remover and Pry Bar

Strips old shingles and pries up flashing without damaging the deck. Clean tear-off is the first step toward a flat, straight panel layout.

Chalk Line and Utility Knife

Marks panel layout and cuts underlayment and ice and water shield to fit around valleys, chimneys, and vents. Straight lines on the underlayment mean straight panels on top.

Roofing Ladder and Safety Harness

Every crew member is tied off on any roof above six feet. We use ladder stabilizers and roof jacks to keep the ladder from damaging the new drip edge.

Caulking Gun with High-Temp Sealant

Seals flashing, pipe boots, and fastener heads with a sealant rated for the temperature swings New York sees. Standard caulk cracks in one winter.

Real results

Before and after.

Albany Colonial: Shingles to Standing Seam

Before

A 2,200-square-foot colonial with three layers of asphalt shingles, curling at the south-facing slope, and a history of ice dams every February. Two ceiling stains in the upstairs hallway and soggy insulation in the attic.

After

We stripped all three layers, replaced four sheets of rotted sheathing, installed ice and water shield at the eaves, and put down 24-gauge standing seam panels in dark bronze. No ice dams the following winter, attic temps down 15 degrees in July.

Coram Ranch: Storm-Damaged Metal Repair

Before

A nor'easter lifted six panels off the west slope and tore the flashing around the chimney. Water was coming into the living room ceiling and the homeowner's insurance adjuster needed documentation before approving the claim.

After

We tarped the same night, photographed every damaged panel and the wet deck underneath, and submitted the report to the adjuster. Three days later we replaced the six panels, re-seamed the run, and installed new chimney flashing. Claim approved, no leaks since.

North Tonawanda Commercial: Flat Roof to Standing Seam

Before

A 4,000-square-foot commercial building with a flat roof that ponded water after every rain and leaked into the tenant space below. Three previous flat roof replacements in 20 years, each one failing within five.

After

We installed a standing seam metal roof over a tapered insulation system that added slope toward the drains, plus new flashing at the parapet walls. Standing water gone, leaks stopped, and a roof rated for 50-plus years.

Problems we solve

Metal Roofing Problems We Solve Across New York

Most of the calls we get are about the same handful of failures: ice dams, flashing leaks, storm damage, and shingles that have simply run out of life. Here is how we handle each one.

Ask a pro →
01

Ice dams backing water under the roof

We install a full ice and water shield membrane at the eaves and valleys, then top it with a metal panel that sheds snow before it can refreeze. On existing metal roofs, we add heat cable at the eave and reseal the flashing.

↗
02

Flashing failure around chimneys and skylights

We cut out the old flashing, install new step and counter flashing, and seal with a caulking gun rated for the temperature swings New York sees. Every penetration gets hose-tested before we sign off.

↗
03

Lifted or missing panels after a storm

We tarp the same day, photograph the damage for your claim, and order matching panels. Once the weather clears, we replace the damaged run and re-seam the whole section so the wind rating is restored.

↗
04

Curling shingles and granule loss on an aging roof

We quote a full metal replacement with a 50-year panel and finish warranty. If the deck is sound, we can often install metal over the existing shingles with a proper underlayment, saving you the tear-off cost.

↗
Proof you can check

Licensed, Insured, and Warrantied in New York

✓
New York State Licensed Home Improvement ContractorNew York State Department of State
✓
OSHA Safety CertificationOccupational Safety and Health Administration
✓
GAF Master EliteGAF
✓
Owens Corning Preferred ContractorOwens Corning
✓
NRCA MembershipNational Roofing Contractors Association
Customer reviews

Reviews From New York Metal Roof Customers

★★★★★
“We had ice dams three winters in a row and finally gave up on shingles. Roofnexa measured the roof, ordered standing seam panels cut to length, and had the whole thing on in five days. No more ice at the eave, and the attic is noticeably cooler in July. Crew swept the yard for nails twice.”
DR

Dan R.Homeowner, Albany

✓ Verified
★★★★★
“A nor'easter peeled back a section of our old metal roof and water was coming into the kitchen. They tarped it the same night and came back three days later to replace the damaged panels and re-seam the whole run. Insurance covered it and the paperwork they gave me made the claim easy.”
KL

Kevin L.Homeowner, North Tonawanda

✓ Verified
Good questions

Frequently Asked Questions About Metal Roofing in New York

(315) 503-7248 →

Most residential metal roof installations in New York run $12 to $22 per square foot installed in 2026, or roughly $18,000 to $45,000 for a typical 1,800- to 2,500-square-foot home. Standing seam sits at the top of that range because of the roll-forming, clips, and mechanical seaming. Exposed-fastener panels land lower. Steep pitches, complex valleys, and multiple chimneys add labor.

A 24-gauge standing seam roof with a Kynar 500 finish typically lasts 50 years or more in New York, and the finish itself carries a 30- to 50-year warranty. Exposed-fastener panels run 25 to 40 years depending on the washers and how often fasteners are re-tightened. Coastal salt air shortens the life of lower-grade steel, which is why we spec aluminum or Galvalume near the shore.

Yes, metal is one of the best winter roof systems for New York. The smooth surface sheds snow at low pitches, which reduces ice dam formation at the eave and keeps weight off the structure. We install a full ice and water shield membrane at the eaves and valleys on every metal roof, and we size clips for the snow load your town requires.

Roofnexa NY installs standing seam and exposed-fastener metal roofs across New York, from Albany and Glens Falls to Coram, Uniondale, and the Buffalo suburbs. We are a state-licensed home improvement contractor with OSHA-certified crews and 12 years in business. Call (315) 503-7248 for a free same-day estimate.

Where we deliver this service

Cities We Serve for Metal Roofing in New York

We install and repair metal roofing in New York across the whole state, from the Capital Region and Adirondack foothills to Long Island and the Buffalo-Niagara metro. Crews are dispatched from regional hubs so we can be on site fast, whether you need a new standing seam roof or a metal roof repair New York homeowners can count on after a storm.

AlbanyStanding seam and exposed-fastener metal roofs for Albany's mix of historic rowhouses and post-war colonials. We size every install for Capital Region snow loads and ice dam risk.View area →Glens FallsAdirondack foothills metal roofing built for heavy snow and hard freeze-thaw cycles. Full ice and water shield at the eaves and clips sized for 50-plus psf snow loads.View area →CoramLong Island metal roofing with Galvalume or aluminum panels and stainless fasteners to resist salt spray. Wind uplift clips sized for the local hurricane-wind zone.View area →UniondaleNassau County metal roof installation and repair, including storm-damage documentation for insurance claims. We handle tear-off, deck repair, and full flashing replacement.View area →North TonawandaLake-effect snow belt metal roofing. We spec panels and clips for 40-plus psf snow loads and add snow guards above doorways and walkways to keep sliding snow safe.View area →AuburnFinger Lakes metal roofing with balanced attic ventilation to prevent condensation. Standing seam and exposed-fastener panels for homes, garages, and outbuildings.View area →Garden CityHigh-end residential metal roofing with custom panel colors and profiles that match the village's architectural character. Full tear-off and deck inspection on every job.View area →LockportNiagara County metal roof installation and repair, including barn and outbuilding panels. Ice and water shield at the eaves and new flashing at every penetration.View area →RooseveltNassau County metal roofing for ranches and capes, with storm-damage repair and insurance documentation. We tarp the same day and schedule permanent repairs fast.View area →North BabylonSouth Shore metal roofing built for salt air and nor'easters. Galvalume panels, stainless fasteners, and clip schedules sized for the local wind uplift requirement.View area →FarmingvilleSuffolk County metal roof installation, repair, and maintenance. We handle everything from a single lifted panel to a full standing seam replacement.View area →BataviaGenesee County metal roofing for farmhouses, barns, and residential homes. Exposed-fastener and standing seam panels sized for western New York snow loads.View area →New CasselNassau County metal roofing with same-day estimates and written scopes. We repair storm damage, replace failed flashing, and install new standing seam systems.View area →Rocky PointNorth Shore Long Island metal roofing with corrosion-resistant panels and stainless fasteners. Full ice and water shield at the eaves and new ridge ventilation.View area →North WantaghSouth Shore metal roof installation and repair, including post-storm inspections and insurance documentation. Standing seam and exposed-fastener systems available.View area →
Ready when you are

Get a Free Metal Roofing in New York Estimate Today

Call (315) 503-7248 and we will inspect your roof, photograph the problem areas, and hand you a written price the same day. Licensed, insured, and 12 years serving New York. No pressure, no surprises.

Get Free Estimate (315) 503-7248 →
Request an appointment

Get Your Free Roofing Estimate

Call (315) 503-7248 or email info@roofnexany.com and we will schedule a free inspection at your property. We answer the phone 24/7 for emergencies, and standard estimates are booked within two business days. Tell us your address and what you are seeing, and we will tell you what it takes to fix it.

Tap to call(315) 503-7248